VYRCO | 22 | v1.0 | 2026-10-31 | REFERENCE GUIDE - DOES NOT AUTHORIZE OPERATIONS Steel and delivery condition: review before machining How to use the worksheet Use one worksheet per parent stock item and record revision; attach additional records when needed. Retain original documents in your authorized system and link them by ID. The PDF and HTML are for reference and printing, with no editable fields. Save the TXT and edit a local copy. Enter pending for missing evidence and explain not applicable. Do not upload internal documents to VYRCO. Blank worksheet 01. Record ID / revision / date / author ________________________________________________________________ 02. Component / drawing / revision / order and line item ________________________________________________________________ 03. Required material / final condition / hardness if applicable / source ________________________________________________________________ 04. Supplier / receipt / parent stock ID ________________________________________________________________ 05. Declared identifiers / supplier's terminology ________________________________________________________________ 06. Material document / ID / revision or date / link to stock ________________________________________________________________ 07. Declared grade / delivery condition / evidence / discrepancies ________________________________________________________________ 08. Required checks / criterion and source / responsible person ________________________________________________________________ 09. Current hardness or other reports / result / scale / method / location ________________________________________________________________ 10. Parent -> cut blanks and remainder map / identification procedure ________________________________________________________________ 11. Open question / impact / required evidence / owner / due date ________________________________________________________________ 12. Recorded disposition / authorized person / scope / reference / date ________________________________________________________________ Limits and authorized decisions Does not select steels, equivalencies, hardness values, tolerances, conversion scales, heat-treatment cycles, machining allowances, marking methods, or machining parameters. Does not verify certificate authenticity or regulatory or legal conformity. Material disposition and testing require authorized judgment and applicable documentation. Original FICTIONAL case: two cut blanks, an incomplete link Requirement: Record DEMO-MAT-01, component INS-DEMO, drawing D-DEMO revision B. Fictional designation ACERO-DEMO-X and condition ESTADO-DEMO-A. These labels are invented; they are not a commercial grade or a recommended treatment. Receipt: Bar DEMO-B01; document DEMO-CERT-07. The bar label states L-DEMO-17, while the received document states L-DEMO-71. A link showing that both codes refer to the same material has not been established. Proposed division: Cut blanks DEMO-C01 and DEMO-C02, with remainder DEMO-R01. The map is prepared, but the cut is not recorded as performed and the bar's evidence is not assigned to the blanks while the link remains unresolved. Review: Status: PENDING. Evidence requested: a documented supplier clarification and review by the designated responsible person. No hardness, composition, or acceptance result is invented. The worksheet does not authorize manufacturing or treating the material. Follow-up: Fictional owner: REVISOR-DEMO. Close the question with a reference to the received evidence and record the authorized decision separately. If a document is corrected, retain its previous version and the reason for the change. Check with the fictional case Use test with the fictional case: another reader must locate the L-DEMO-17 versus L-DEMO-71 discrepancy, identify the missing evidence, and confirm that the blanks do not yet have an established link. If the worksheet implies automatic conformity, the review is incomplete. Sources, scope, and review Manufacturer descriptions are limited to the cited points. The sequence, worksheet, question classification, and example are original VYRCO guidance, not requirements issued by Uddeholm or BÖHLER. No third-party tables, images, or process parameters are reproduced. U-HT | https://www.uddeholm.com/us/en-us/services/heat-treatment/ Accessed: 2026-10-30 Manufacturer says its tool steels are normally supplied soft annealed; general context only. Not a universal rule, shipment certificate, grade selection, or processing instruction. No heat-treatment parameters adopted. U-IMPAX | https://www.uddeholm.com/us/en-us/products/uddeholm-impax-supreme/ Accessed: 2026-10-30 Overview identifies Impax Supreme as prehardened mold steel. Used only to show delivery condition must be checked for the exact product. No grade equivalence, hardness range, treatment, or suitability recommendation adopted. Page heading/application taxonomy is inconsistent; only explicit overview statement used. B-TEST | https://www.bohler-edelstahl.com/en/services/testing-certification/ Accessed: 2026-10-30 Public page distinguishes chemical analysis, mechanical testing including hardness testing, and certification activities. No testing procedure or required certificate class inferred. Accreditation and conformity of any supplier or VYRCO are not assessed. VYRCO | info@vyrco.com